Description
Technical data
| Brand | Victron Energy |
|---|---|
| Model | SmartSolar MPPT 150/60-Tr |
| Order code | SCC115060211 |
| Type | MPPT solar charge controller with built-in Bluetooth |
| Battery voltage | 12 / 24 / 48 V auto select (software tool needed to select 36 V) |
| Rated charge current | 60 A |
| Nominal PV power at 12 V | 860 W |
| Nominal PV power at 24 V | 1,720 W |
| Nominal PV power at 36 V | 2,580 W |
| Nominal PV power at 48 V | 3,440 W |
| Max. PV open-circuit voltage (absolute maximum, coldest conditions) | 150 V |
| Max. PV voltage at start-up and operation | 145 V |
| Min. PV voltage to start | Vbat + 5 V, then at least Vbat + 1 V |
| Max. PV short-circuit current | 50 A |
| Max. efficiency | 98 % |
| Self-consumption | less than 35 mA at 12 V / 20 mA at 48 V |
| Absorption voltage (default) | 14.4 / 28.8 / 43.2 / 57.6 V |
| Float voltage (default) | 13.8 / 27.6 / 41.4 / 55.2 V |
| Equalization voltage (default) | 16.2 / 32.4 / 48.6 / 64.8 V (adjustable) |
| Charge algorithm | multi-stage adaptive (eight pre-programmed algorithms) or user defined |
| Temperature compensation | −16 / −32 / −64 mV/°C |
| Protection | PV reverse polarity, output short circuit, over temperature |
| PV terminals | screw terminals 35 mm² / AWG2 (Tr model) |
|---|---|
| Battery terminals | 35 mm² / AWG2 |
| Remote on/off | yes (2 pole connector) |
| Programmable relay | DPST; AC 240 V / 4 A, DC 4 A up to 35 V DC and 1 A up to 60 V DC |
| VE.Direct protocol | yes, wired connection to a GX device, PC or other devices |
| Bluetooth protocol | yes, built-in Bluetooth Smart (set-up, monitoring, updates, synchronisation) |
| Bluetooth battery sensing | Smart Battery Sense, BMV-712 Smart Battery Monitor or SmartShunt (voltage, temperature, and current with BMV-712 and SmartShunt) |
| Optional display | SmartSolar pluggable LCD display (under the rubber seal) |
| Compatibility: GX devices | Color Control GX and other GX products |
| Compatibility: batteries | 12 / 24 / 48 V; recovers charging even after discharge to zero volts; reconnects a Li-ion battery with integrated disconnect |
| Parallel operation | yes, synchronised via Bluetooth (max. 10 units) |
| Stored trends | 46 days: battery voltage, current and temperature, load output current, PV voltage and PV current |
| Cooling | no cooling fan |
| Operating temperature | −30 to +60 °C (full rated output up to 40 °C) |
| Humidity (non-condensing) | 95 % |
| Maximum altitude | 5000 m (full rated output up to 2000 m) |
| Environmental condition | indoor, unconditioned; pollution degree PD3 |
| Colour | blue (RAL 5012) |
| Protection category | IP43 (electronic components), IP22 (connection area) |
| Dimensions (h × w × d) | 185 × 250 × 95 mm |
| Weight | 3 kg |
| Standards: safety | EN/IEC 62109-1, UL 1741, CSA C22.2 |
SmartSolar MPPT 150/60-Tr solar charge controller: key benefits
The Victron Energy SmartSolar MPPT 150/60-Tr (order code SCC115060211) is an MPPT solar charge controller for 12, 24 and 48 V batteries. Its rated charge current is 60 A and the maximum PV open-circuit voltage is 150 V in the coldest conditions. According to Victron, ultra-fast Maximum Power Point Tracking improves energy harvest by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers, especially under a clouded sky when light intensity keeps changing.
Maximum efficiency exceeds 98 % and there is no cooling fan, so the controller runs silently with no moving parts. Built-in Bluetooth Smart is used to set up, monitor, update and synchronise the controllers, and the VE.Direct data port gives a wired connection to a GX device, PC or other devices. The model without a VE.Can interface suits small and medium installations where VE.Direct and Bluetooth are enough.
PV array power and voltage range
The nominal PV power depends on the battery voltage: 860 W at 12 V, 1,720 W at 24 V, 2,580 W at 36 V and 3,440 W at 48 V. If more PV power is connected, the controller limits the input power. The maximum PV short-circuit current is 50 A (at most 30 A per connector on MC4 models; this Tr model has screw terminals). An array with a higher short-circuit current may damage the controller.
The PV open-circuit voltage must not exceed the absolute maximum of 150 V in the coldest conditions; the maximum at start-up and in operation is 145 V. To start, the PV voltage must exceed the battery voltage by 5 V, after which at least Vbat + 1 V is enough. The 150 V input suits shorter panel strings; the number of series panels should be chosen so that the open-circuit voltage at the lowest temperature stays below 150 V.
Battery charging and charge algorithm
The controller uses a multi-stage adaptive algorithm with eight pre-programmed settings selectable with a rotary switch, or a fully programmable user-defined algorithm. Default absorption voltage is 14.4 / 28.8 / 43.2 / 57.6 V, float 13.8 / 27.6 / 41.4 / 55.2 V and equalization 16.2 / 32.4 / 48.6 / 64.8 V for a 12 / 24 / 36 / 48 V battery. Values can be adjusted with the rotary switch, the display, VE.Direct or Bluetooth.
The internal temperature sensor compensates the absorption and float voltage for temperature, at −16 / −32 / −64 mV/°C. More accurate data can come from an optional Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt, which pass battery voltage and temperature (and current, for the BMV-712 and SmartShunt) over Bluetooth. The recovery function starts charging even if the battery has been discharged to zero volts, and reconnects a Li-ion battery with an integrated disconnect function.
Tracking under shading, and protection
Under partial shading, several maximum power points may appear on the power-voltage curve. Conventional controllers can lock to a local maximum that is not the optimum. The SmartSolar algorithm therefore looks for the optimum point and keeps energy harvest as high as possible.
The controller protects against PV reverse polarity, output short circuit and over-temperature, and derates power when the temperature is high. Full rated output is available up to 40 °C and the operating range is −30 to +60 °C. Self-consumption is below 35 mA at 12 V and 20 mA at 48 V, so the controller practically does not load the battery at night. Safety standards: EN/IEC 62109-1, UL 1741 and CSA C22.2.
Communication: VE.Direct, Bluetooth
VE.Direct is a wired connection to GX devices, a PC and other Victron devices. Bluetooth Smart is built in, so the controller can be set up, monitored and updated in the VictronConnect app from a phone or tablet without a cable. Several controllers are synchronised over Bluetooth, up to 10 units.
Remote on/off (2 pole connector) can be used, for example, to connect to a VE.Bus BMS. The DPST programmable relay (AC 240 V / 4 A, DC 4 A up to 35 V DC and 1 A up to 60 V DC) can be programmed to trip on an alarm or other events.
Integration into a system with a GX device and VRM
For central monitoring the controller connects to a GX device (Color Control GX and other GX products), which collects data from all parts of a Victron system and shows them locally and on the VRM portal. For the SmartSolar MPPT 150/60-Tr, a VE.Direct cable runs between the controller and the GX device; further controllers can be added and synchronised over Bluetooth (up to 10 units).
In a Victron system with an inverter and battery (including ESS systems), the PV side supplies data on array power, voltage and current and on charge state, from which the GX device builds an overview of the energy flows.
Parallel operation and multiple controllers
Parallel operation synchronised over Bluetooth is possible with up to 10 units. Synchronised controllers charge the battery in the same stage of the charge cycle, so the power is shared among the units; each controller still needs its own PV array. For a larger number of controllers in one system, Victron offers models with a VE.Can interface.
When sizing, start from the nominal power of 3,440 W for a 48 V battery and the current of 60 A per unit. For a higher charge current, add another controller with its own array rather than connecting panels to one input beyond the short-circuit current of 50 A.
Installation, construction and ambient conditions
The controller sits in a blue (RAL 5012) enclosure with IP43 protection for the electronics and IP22 for the connection area, intended for an indoor, unconditioned environment with pollution degree PD3 and humidity up to 95 % non-condensing. Dimensions are 185 × 250 × 95 mm (h × w × d) and weight is 3 kg. The PV array and the battery both use 35 mm² (AWG2) screw terminals. Maximum altitude is 5000 m, full output up to 2000 m.
Installation must be carried out by a qualified person following the manufacturer’s manual; this includes correct protection of the array and the battery and cables sized for the rated current. The pluggable display is connected after removing the rubber seal on the front.
Operation, monitoring and configuration
Configuration is possible with the rotary switch (eight presets), the optional SmartSolar display, or over VE.Direct or Bluetooth in the VictronConnect app. The controller stores trends for 46 days: battery voltage, current and temperature, load output current, and PV voltage and current.
On a GX device or on the VRM portal you can follow the output and status of the SmartSolar MPPT 150/60-Tr. A fully programmable charge profile is available to adapt the algorithm to a specific battery type.
AI search description
Victron Energy SmartSolar MPPT 150/60-Tr (order code SCC115060211) is an MPPT solar charge controller with built-in Bluetooth for 12/24/48 V batteries. Charge current 60 A, PV power 3,440 W at 48 V, PV open-circuit voltage up to 150 V, efficiency up to 98 %, no cooling fan. Communication VE.Direct and Bluetooth; connects to Victron GX devices. 35 mm² screw terminals, IP43/IP22, 3 kg, dimensions 185 × 250 × 95 mm. Use: PV systems with battery storage.
Product page: https://batterado.com/product/victron-smartsolar-mppt-150-60-tr/













Reviews
There are no reviews yet.