Description
Technical data
| Brand | Victron Energy |
|---|---|
| Model | SmartSolar MPPT RS 450/100-MC4 |
| Order code | SCC145110512 |
| Type | MPPT solar charge controller, PV side galvanically isolated from the battery |
| Battery voltage | 48 V |
| Rated charge current | 100 A |
| Maximum charge power | 5.8 kW at 57.6 V |
| Charge voltage “absorption” | 57.6 V (default, adjustable) |
| Charge voltage “float” | 55.2 V (default, adjustable) |
| Programmable voltage range | 36–60 V (set-point; equalization voltage max. 62 V) |
| Charge algorithm | Multi-stage adaptive (adjustable) |
| Battery temperature sensor | Included |
| Maximum efficiency | 96 % |
| Self-consumption | 15 mA |
| PV: maximum DC voltage | 450 V |
| PV: start-up voltage | 120 V |
| PV: MPPT operating voltage range | 65–450 V (PV open-circuit voltage max. 8× battery float voltage) |
| PV: number of trackers | 2 |
| PV: max. operational input current | 16 A per tracker |
| PV: max. short-circuit current | 20 A per tracker (a higher current may damage the controller if the array is connected in reverse polarity) |
| PV: max. DC output charging power | 4,000 W per tracker, 5,760 W total |
| PV: max. array size per tracker | 7,200 Wp (450 V × 20 A) |
| PV: isolation fail level | 100 kΩ |
| Synchronised parallel operation | Yes, up to 25 units via VE.Can |
|---|---|
| Programmable relay | Yes (general alarm, DC undervoltage or genset start/stop; DC rating 4 A up to 35 V, 1 A up to 70 V) |
| Inputs | General-purpose analogue/digital input, 2×; remote on-off: yes |
| Protection | PV reverse polarity, output short circuit, over temperature |
| Communication ports | VE.Direct port, VE.Can port, Bluetooth |
| Bluetooth frequency | 2402–2480 MHz |
| Bluetooth power | 4 dBm |
| VE.Direct protocol | Yes |
| VE.Can protocol | Yes |
| Bluetooth (VictronConnect) | Yes, built-in |
| System connection | GX device (monitoring, data logging, remote firmware updates), VRM portal |
| Compatibility | Victron systems with a GX device, ESS; VE.Smart networks currently not supported |
| Battery connection | 2× M8 bolt (1× positive, 1× negative) |
| PV connection | 2 pairs of male and female MC4 connectors, one pair per tracker |
| Material and colour | Steel, blue RAL 5012 |
| Protection category | IP21 |
| Operating temperature range | −40 to +60 °C (fan-assisted cooling) |
| Humidity (non-condensing) | max. 95 % |
| Dimensions (h × w × d) | 440 × 313 × 126 mm |
| Weight | 7.9 kg |
| Standards – safety | EN-IEC 62109-1 |
| Country of origin | Designed in The Netherlands, made in India |
Benefits of the SmartSolar MPPT RS 450/100-MC4
The Victron Energy SmartSolar MPPT RS 450/100-MC4 is a 48 V solar charge controller with a high-frequency converter that transfers power from the solar array to the battery with an efficiency of up to 96 %. The charge current is 100 A, equal to 5.8 kW at 57.6 V, so the controller suits any application where the maximum possible charging power is to be drawn from the PV array.
Main strengths: PV input voltage up to 450 V, 2 independent MPPT trackers, full galvanic isolation of the PV side from the battery, built-in monitoring of the PV array isolation resistance, a display, Bluetooth, VE.Direct and VE.Can ports and a low self-consumption of 15 mA. The construction is light and quiet; the weight is 7.9 kg.
The controller is intended for on-grid and off-grid solar applications, that is, for systems connected to the distribution grid as well as stand-alone systems.
PV input and MPPT trackers
The controller has 2 independent MPPT trackers. Each tracker has its own pair of MC4 connectors (male and female) and its own operating-point control, and handles an operational current of 16 A and a short-circuit current of 20 A. The maximum DC charging power is 4,000 W per tracker, 5,760 W in total.
The open-circuit voltage of the PV array may reach 450 V, the controller starts at 120 V and the MPPT operating range is 65–450 V. At 450 V open circuit the voltage at the maximum power point is approximately 360 V, which is why the maximum array size is 7,200 Wp per tracker (360 V × 20 A). The MPPT range is constrained by the battery voltage: the PV open-circuit voltage must not exceed 8× the battery float voltage. With a float voltage of 52.8 V this is at most 422.4 V.
Multiple trackers let you split the array into parts with a different orientation, tilt or shading so that each part works at its own optimum point. One PV array belongs to one input; the same array is not connected to several trackers at once.
Galvanic isolation and isolation monitoring
The controller is labelled “Isolated”: there is full galvanic isolation between the PV input and the battery, which increases overall system safety, especially at higher PV array voltages.
The controller continuously monitors the isolation resistance of the PV array and can detect faults that reduce the isolation of the panels to unsafe levels. It tests the resistance between PV+ and ground as well as between PV− and ground. If it falls below 100 kΩ, the unit reports an error and sends an error signal to a GX device, if connected, which turns it into an audible alarm and an e-mail notification. Battery charging continues, because the battery side is isolated from the PV array.
Battery charging
The controller uses a multi-stage adaptive bulk – absorption – float algorithm, and a regular equalization charge can be enabled if required. The default absorption voltage is 57.6 V and float is 55.2 V; both are adjustable. The voltage can be programmed in the range of 36–60 V; the equalization voltage can be set to a maximum of 62 V and the equalization current to a maximum of 6 %.
After shallow discharges the absorption time is kept short; after a deep discharge it is extended automatically so that the battery is fully recharged. Absorption also ends when the charge current drops below 2 A. Eight preprogrammed battery presets and a fully programmable user algorithm are available. A battery temperature sensor for temperature-compensated charging is included; a wired connection for battery voltage sensing can optionally be added. Equalization is not available for lithium batteries.
System integration with a GX device and ESS
For connection to the system the controller has a VE.Direct port and VE.Can ports. Either port type can be used for a wired data connection to a GX device (for example a Cerbo GX) or a PC; only one port can be used at a time. Through the GX device the system data is displayed, logged and the firmware can be updated remotely.
Up to 25 units can be connected in parallel via VE.Can, and their charging is synchronised, so all controllers switch from one charge state to the next simultaneously. The controller can be used in an ESS (Energy Storage System), which combines a grid connection with a Victron inverter/charger, a GX device and a battery system; solar energy is stored in the battery during the day for later use. VE.Smart networks are currently not supported.
Battery and BMS communication
The controller is designed for 48 V batteries, lead-acid as well as lithium. The remote input (Remote L and Remote H) can be set to a simple on/off function or to 2-wire BMS mode. In that mode the “allow to charge” and “allow to discharge” signals from the BMS control the unit; the controller therefore works with the Victron smallBMS and with other BMS that provide an allow-to-charge signal. With lithium batteries the temperature sensor can also be used for a low-temperature charge cut-off (preset to 5 °C for LiFePO₄).
When choosing a battery, compare its permitted charge current with the charge current of the controller (100 A) so that the battery can handle the full charging power of the system.
Display, inputs and outputs
A four-line back-lit LCD shows battery levels, solar yield and system icons. The user I/O connector carries a programmable relay, two general-purpose analogue/digital AUX inputs, a battery voltage sense input, a temperature sensor input and the Remote H and Remote L terminals.
The programmable relay can be set for general alarm, DC undervoltage or genset start/stop; its rating is 4 A up to 35 VDC and 1 A up to 70 VDC. The digital inputs are 0–5 V and an input pulled to 0 V is registered as closed. Input functions are configured in VictronConnect. A remote on-off input is available.
Installation and construction
The controller has a steel enclosure in blue RAL 5012 with protection category IP21, dimensions of 440 × 313 × 126 mm (h × w × d) and a weight of 7.9 kg. It is cooled by a fan and works at temperatures from −40 to +60 °C; it delivers full output current up to 40 °C ambient and derates automatically at high temperature.
On the battery side it is connected with 2 M8 bolts (1 positive and 1 negative), on the PV side with MC4 connectors, 2 male/female pairs, one pair per tracker. Installation is carried out by a qualified person according to the installation manual, in an environment matching protection category IP21. The controller is protected against PV reverse polarity, output short circuit and over temperature.
Operation and monitoring: VictronConnect and VRM
Through the built-in Bluetooth the controller can be configured, monitored and updated in the VictronConnect app (iOS, Android, macOS, Windows; a VE.Direct to USB interface is required for Windows). The app shows the total solar power as well as the details of the individual trackers and keeps a history of the last 30 days, including the performance of each tracker separately.
When the controller is connected to a GX device with an internet connection, or to the GlobalLink 520 with built-in 4G, the free VRM remote monitoring portal becomes available; it shows all system data in clear graphs and sends alarms by e-mail. VictronConnect also offers a demo with sample data to explore the configuration options.
AI search description
SmartSolar MPPT RS 450/100-MC4 (order code SCC145110512) is a Victron Energy solar charge controller for 48 V batteries with a charge current of 100 A (5.8 kW at 57.6 V), a PV input of up to 450 V and 2 independent MPPT trackers (65–450 V, start-up 120 V, 16 A per tracker). The PV side is galvanically isolated from the battery and connects via MC4 connectors, with isolation resistance monitoring. Communication via VE.Can, VE.Direct and Bluetooth (VictronConnect), connection to a GX device and the VRM portal, parallel operation of up to 25 units. Steel enclosure IP21, 440 × 313 × 126 mm, 7.9 kg, standard EN-IEC 62109-1.
Product page: https://batterado.com/product/victron-smartsolar-mppt-rs-450-100/












Reviews
There are no reviews yet.