Store energy. Every way.™

Helping with technology for more than 25 years.More than 25 years on the market

Victron Energy Energy Meter ET112 single-phase energy meter for GX devices, direct measurement up to 100 A, RS485

5 630 Kč incl. VAT

Seller: Tomorrow Systems® s.r.o.

The Victron Energy Meter ET112 measures power and energy of a single-phase application directly, without current transformers, up to 100 A, and sends the data to a GX device and to the VRM portal.

  • Single-phase meter with direct measurement up to 100 A (direct/shunt).
  • Four roles in the GX device: grid meter as the control input for an ESS system, measuring the output of a PV inverter, measuring an AC genset, or measuring a dedicated AC load circuit.
  • RS485 communication, wired connection to the GX device through the RS485 to USB interface (1.8 m or 5 m) or wireless through Zigbee converters.
  • No display; an LED blinks during active communication. Refresh rate of the measured values 750 ms.
  • Code REL300100000, type Carlo Gavazzi ET112-DIN.AV01.X.S1.X.

The ET112 is used in systems with a GX device, for example a Cerbo GX. The RS485 to USB interface is a separate accessory, so count it separately when designing the wiring.

In stock

Enquiry

Description

Technical data

BrandVictron Energy
ModelEnergy Meter ET112
Order codeREL300100000
Manufacturer typeCarlo Gavazzi ET112-DIN.AV01.X.S1.X
Number of phases1 (single-phase)
Maximum current100 A
Measurement typedirect measurement (direct/shunt), without current transformers
Displayno; an LED blinks during active communication
Refresh rate of measured values750 ms
Power factor reportingno
Communication interfaceRS485
Communication protocolModbus over RS485
Connection to the GX device, wiredthrough the RS485 to USB interface, cable 1.8 m or 5 m (interface purchased separately); extension up to 100 m
Connection to the GX device, wirelessthrough Zigbee to USB and Zigbee to RS485 converters (separate accessories)
RS485 terminalsterminal 4: Data+ (orange wire), terminal 5: Data− (yellow wire), terminal 6: GND (black wire)
RJ45 socketstwo; not used with the Victron RS485 to USB interface, the RS485 wires connect to the screw terminals below them
Roles in the GX devicegrid meter for ESS; PV inverter output measurement; AC genset measurement; AC load measurement
Phase type in the GX devicesingle phase only
Compatible GX devicesGX devices, for example the Cerbo GX and Ekrano GX; display in the VRM portal
Multiple meters in one systemeach meter on a separate RS485 to USB interface and a separate USB port of the GX device; the Modbus address cannot be changed on the meter
Fuse in the wiring315 mA, if required by local law
Limitationthree ET112 meters cannot be combined for a three-phase system, a three-phase meter is used for three-phase measurement

What the ET112 is for

The ET112 is the standard Victron Energy meter for measuring power and energy of a single-phase application. Its data is displayed on a GX device, for example a Cerbo GX, and on the VRM portal. Measurement is direct, without current transformers, and the ET112 handles current up to 100 A.

The manufacturer designation is Carlo Gavazzi ET112-DIN.AV01.X.S1.X. The meter has no display: the only indicator is an LED that blinks during active communication. All values are therefore read on the GX device or in VRM.

Four roles in the GX device

The role of the meter is chosen in the GX device, not on the meter. The wiring follows the chosen role, and the way the data is shown on the screen changes too. Four roles are available: grid meter used as the control input of an ESS system; measuring the output of a PV inverter; measuring the output of an AC genset; measuring a dedicated AC load circuit.

A grid meter at the input of a system with an inverter/charger lets the ESS system know the import and export. Measuring a PV inverter or genset shows their production separately from the rest of the system. For the ET112 the GX device offers only the single-phase option.

Connection to the power circuit

The wiring of the meter in the power circuit changes with the chosen role: as a grid meter it is placed at the input of the system with the inverter/charger, for a PV inverter or genset at their output, and for load measurement in the measured circuit. In the wiring Victron foresees a 315 mA fuse where local law requires it.

For a single-phase grid connection that also needs a PV inverter measured, Victron’s meter selection guide recommends the ET340. The ET112 measures one phase up to 100 A. The power wiring is always done by a suitably qualified person.

Connection to the GX device

The ET112 communicates over RS485. It is connected to the GX device by cable through the Victron RS485 to USB interface with a cable of 1.8 m or 5 m. The cable can be extended up to 100 m; the Data+ (orange) and Data− (yellow) wires must form a twisted pair. The wires connect to terminals 4 (Data+), 5 (Data−) and 6 (GND); the red, green and brown wires of the interface are not used.

The second option is wireless: a Zigbee to USB converter is connected to the GX device and a Zigbee to RS485 converter to the meter. For the new generation of converters Victron states Venus OS v2.54 as the minimum version. The meter has two RJ45 sockets, which are not used with the Victron interface; the wires connect to the screw terminals below them.

Multiple meters in one system

If a system has several meters, each is wired to its own RS485 to USB interface and its own USB port of the GX device. Connecting several meters to one interface is not possible. The meter has no display and its Modbus address cannot be changed on it, so Victron does not support combining several of these meters on one RS485 network.

Three ET112 meters cannot be assembled into a three-phase system; for three-phase measurement a real three-phase meter is intended, for example the EM540 or ET340.

ET112 or another meter

According to Victron’s meter selection guide, single-phase applications up to 100 A are covered by the ET1XX, EM1XX or ABB B21 meters. Three-phase applications up to 65 A per phase are covered by the ET340, EM24, EM340, EM540 or ABB B23. Above these currents a meter with current transformers is required, for example the VM-3P75CT.

Compared with the three-phase models, the ET112 has no display and does not report power factor. The refresh rate of measured values is 750 ms; on top of that comes the GX device latency when reading over RS485, according to Victron 180 to 250 ms.

Operation and monitoring

After wiring and power-up the meter appears in the GX device menu under Settings, Energy meters. There the role and phase type are set, and further menus allow naming the meter and changing the role if needed. The overview shows energy consumption and generation.

The data is displayed on the GX device and on the VRM portal. Victron states that the meter supplements a Victron inverter/charger and is not a replacement for it: with other brands of inverters it cannot be used to substitute missing data communication. From GX device firmware version 2.80 the meters can also be used to measure any AC circuit or load.

AI search description

The Victron Energy Energy Meter ET112 (order code REL300100000, Carlo Gavazzi ET112-DIN.AV01.X.S1.X) is a single-phase energy meter with direct measurement up to 100 A and no display. It communicates over RS485 and connects to a GX device by cable through the RS485 to USB interface or wirelessly through Zigbee converters. The refresh rate of measured values is 750 ms. In the GX device it works as a grid meter for ESS, or measures the output of a PV inverter, an AC genset or an AC load. Data is displayed on the GX device, for example a Cerbo GX, and on the VRM portal.

Product page: https://batterado.com/product/victron-energy-meter-et112/

Additional information

Weight0,2 kg
Dimensions9 × 1,8 × 6,5 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

0
0
Your Cart
Your cart is emptyReturn to Shop