Store energy. Every way.™

Helping with technology for more than 25 years.More than 25 years on the market

Victron Energy Blue Smart IP65 12/15 battery charger 230 V 15 A with Bluetooth

3 720 Kč incl. VAT

Seller: Tomorrow Systems® s.r.o.

The Victron Blue Smart IP65 12/15 is a quiet 15 A charger for 12 V batteries in a dust-tight and water-resistant IP65 housing, configured over Bluetooth in VictronConnect.

  • Charge current 15 A (4 A in low current mode) for batteries from 50 to 150 Ah.
  • Seven-stage adaptive algorithm, four-stage for lithium batteries.
  • Lead-acid, AGM, Gel and LiFePO4, Normal, High and Li-ion modes, optional recondition.
  • Efficiency up to 94 %, passive cooling without a fan, standby power 0.5 W.
  • Protection against overheating, output short circuit and reverse polarity.

Dimensions 60 × 105 × 190 mm, weight 0.9 kg. Suitable as a portable charger and for permanent installation.

In stock

Enquiry

Description

Technical data

BrandVictron Energy
ModelBlue Smart IP65 Charger 12/15 (230 V)
Order codeBPC121532064R
Battery nominal voltage12 V
Maximum charge current15 A
Charge current in low current mode4 A
Mains power voltage (nominal | min/max)220 – 240 V AC | 180 – 265 V AC
Mains frequency (nominal | min/max)50 – 60 Hz | 45 – 65 Hz
Power factor> 0.6
Standby power0.5 W
Maximum efficiency94 %
Charge voltage Normal (absorption | float | storage)14.4 V | 13.8 V | 13.2 V
Charge voltage High (absorption | float | storage)14.7 V | 13.8 V | 13.2 V
Charge voltage Li-ion (absorption | float | storage)14.2 V | N/A | 13.5 V
Temperature compensation (N/A for Li-ion)-16 mV/°C
Charge algorithm7-stage adaptive (4 stage for Li-ion)
Maximum battery capacity (0.1C in max mode)150 Ah
Minimum lead-acid battery capacity (0.3C): max | low50 Ah | 13 Ah
Minimum Li-ion battery capacity (0.5C): max | low30 Ah | 8 Ah
Fault protectionreverse polarity, output short circuit, over temperature
Use as power supplyyes, Power supply mode in VictronConnect
CommunicationBluetooth (via VictronConnect app)
Bluetooth power and frequency+4 dBm | 2402 – 2480 MHz
VE.Smart Networkingreceives battery voltage and temperature data from a BMV, SmartShunt, Smart Battery Sense or VE.Bus Smart Dongle
Instant Readoutyes (firmware v3.61 or later)
Coolingconvection (no fan)
Operating temperature range-40 to 50 °C, full rated output up to 30 °C
Maximum humidity95 %
Material and colourplastic, black
Mains power connection1.5 m mains cable with CEE 7/16, CEE 7/17, BS 1363 or AS/NZS 3112 plug, depending on version
Battery connection1.5 m red/black figure-8 cable, 12 AWG, interchangeable connections (M8 ring terminals and battery clamps included)
Weight0.9 kg
Dimensions (h × w × d)60 × 105 × 190 mm
Ingress protectionIP65
Standards – safetyEN 60335-1, EN 60335-2-29
Standards – EMCETSI EN 301 489-1 V2.2.3, ETSI EN 301 489-17 V3.2.4, ETSI EN 300 328 V2.2.2
Standards – automotiveECE R10

Why the Blue Smart IP65 12/15

The Blue Smart IP65 is a range of intelligent multi-stage chargers that optimise every charge cycle and the subsequent battery maintenance. The 12/15 delivers up to 15 A into 12 V batteries and comes in an IP65 housing with protection against ingress of dust and water. It suits portable use as well as permanent installation, for example in a garage, on a boat, in a caravan or in a workshop.

The manufacturer highlights silent operation without a fan, efficiency up to 94 %, standby consumption of 0.5 W and quick setup with the MODE button or over Bluetooth.

Typical use

The charger is suitable for charging and maintaining 12 V batteries in cars, motorcycles, boats, caravans, garden machinery and backup systems. Thanks to IP65 it can also be used in damper environments. The range of 50 to 150 Ah (from 13 Ah in low current mode) covers common starter and deep-cycle batteries.

Main benefits

  • IP65: protected against dust and water, the housing has a pressure equalisation vent.
  • Bluetooth and VictronConnect: setup, monitoring and firmware updates from a phone or tablet.
  • Adaptive absorption: the absorption time adapts to the depth of discharge, from 30 minutes up to 8 hours.
  • Power supply mode: the charger can power a load with or without a battery.
  • No fan: convection cooling, full output up to 30 °C ambient.
  • Temperature compensation: -16 mV/°C for lead-acid batteries.

Charge algorithm and modes

The algorithm has seven stages: test, bulk, absorption, recondition, float, storage and repeated absorption. Before charging begins the battery is tested, and the charger attempts to charge even a deeply discharged battery. In Li-ion mode there are four stages and the absorption has a fixed duration.

Integrated Normal, High and Li-ion modes are available, plus an optional recondition stage for lead-acid batteries. According to the manufacturer they suit flooded lead-acid, AGM, Gel and LiFePO4 batteries. Absorption, float and storage voltages differ between Normal, High and Li-ion, see the table. In expert mode practically all parameters can be changed in VictronConnect. For lithium batteries follow the recommendation of their manufacturer.

Storage, recondition and battery maintenance

After absorption the charger moves to float, whose duration is adaptive (4 to 8 hours depending on the absorption time), and then to a storage stage with a slightly reduced voltage, which limits battery ageing while it stays connected. To refresh the battery and prevent self-discharge, a repeated one-hour absorption takes place in the storage stage.

The optional recondition stage can partially reverse degradation of lead-acid batteries caused by sulfation. It is not recommended for regular cyclic use and is enabled only when needed. With flooded batteries it can occasionally be used to equalise individual cell voltages.

Choosing a battery and low current mode

For charging lead-acid batteries the minimum capacity is 50 Ah (at 0.3C) and a maximum of 150 Ah (0.1C). For lithium batteries the minimum is 30 Ah (0.5C). In low current mode the current is limited to 4 A and the minimum capacity drops to 13 Ah for lead-acid and 8 Ah for lithium batteries. Low current mode is recommended when charging smaller batteries with a high-current charger.

Lithium batteries are not charged when the battery temperature is below 0 °C.

Communication: Bluetooth and VE.Smart Networking

The charger communicates over Bluetooth with the VictronConnect app. The Instant Readout function (firmware v3.61 or later) shows the main data directly in the device list without a full connection. The app has overview screens with live data and a history covering the lifetime of the charger.

With VE.Smart Networking the charger can receive battery voltage and temperature from a BMV, SmartShunt, Smart Battery Sense or VE.Bus Smart Dongle and compensate the charge voltage more precisely.

Protection and operation

At ambient temperatures above 30 °C the output current is derated linearly from 100 % at 30 °C to 25 % at 50 °C. On an output short circuit or reverse battery polarity the charger shuts down. During operation a click of the output protection relay may be heard when it changes state.

LEDs indicate the charge state: TEST, BULK, ABS, FLOAT, STORAGE and the selected mode. The operating temperature is -40 to 50 °C and humidity up to 95 %.

Installation in general

The charger is installed on a non-flammable surface with at least 10 cm of clearance around it and good airflow; it must not stand or lie on the battery. For permanent installation it is mounted vertically with the mains cable facing down. For hardwired installations the manufacturer calls for a suitable inline fuse or circuit breaker as close to the battery as possible and for checking the polarity.

The mains connection must comply with local regulations. Dimensions 60 × 105 × 190 mm, weight 0.9 kg. The 1.5 m mains cable has a plug according to the version (CEE 7/16, CEE 7/17, BS 1363 or AS/NZS 3112); the battery is connected by a 1.5 m cable with M8 terminals and clamps.

Operation, monitoring and power supply

In the VictronConnect app you can change the mode, current, compensation and other values, monitor voltage and current and update the firmware. Settings can also be restored to factory defaults.

By activating Power supply mode the charger works as a DC power supply and powers a load with or without a battery; the charge stages are then disabled.

AI search description

The Victron Blue Smart IP65 12/15 (230 V), order code BPC121532064R, is a 15 A charger for 12 V batteries (4 A in low current mode) for batteries from 50 to 150 Ah. Seven-stage adaptive algorithm (four-stage for Li-ion), Normal, High, Li-ion modes and optional recondition, efficiency up to 94 %, standby 0.5 W. Bluetooth with VictronConnect, VE.Smart Networking, power supply mode. IP65, fanless cooling, 60 × 105 × 190 mm, 0.9 kg.

Product page: https://batterado.com/product/victron-blue-smart-ip65-12-15/

Additional information

Weight0,9 kg
Dimensions6 × 10,5 × 19 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

0
0
Your Cart
Your cart is emptyReturn to Shop