Description
Technical data
| Brand | Felicity Solar |
|---|---|
| Model | LPBA48100-OL |
| Type | Low-voltage battery unit for wall or floor installation |
| Chemistry | LiFePO4 |
| Nominal voltage | 51.2 V |
| Operating voltage | 44.8–57.6 V |
| Capacity | 100 Ah |
| Nominal energy | 5.12 kWh |
| Recommended charge / discharge current | 50 A |
| Max. continuous charge / discharge current | 60 A (depends on temperature and state of charge) |
| Peak current (15 s) | 100 A |
| Depth of discharge (DoD) | ≥ 95% |
| Cycle life | ≥ 6,000 cycles (0.2C, 25 °C, 80% DoD) |
| Parallel connection | Up to 12 units (61.44 kWh) |
| Cell type | LiFePO4 |
| Protection | Built-in smart BMS, breaker and fuse (the fuse can be replaced from the outside) |
| Fire protection | Aerosol fire-extinguishing system, vent valve |
| Series connection of units | Not supported |
| Communication | RS485 / CAN |
| Communication ports | Port G (RS485, Felicity inverters), port H PCS (CAN / RS485, inverters of other brands), LINK-0 and LINK-1 (parallel communication) |
| PCS port pinout (battery side) | 1 COM-GND, 5 RS485-B, 6 RS485-A, 7 CANL-PCS, 8 CANH-PCS |
| PCS port wiring on the inverter side (CAN) | 7 CANL-PCS, 8 CANH-PCS |
| Communication cables | Grey: RS485 for Felicity inverters; blue: CAN or RS485 for inverters of other brands; yellow: universal RJ45 to eight loose wires; black: parallel communication between batteries |
| Power connection | Two power cables 0.9 m / 25 mm² (up to 125 A) with crimp terminals, PE earth connection |
| Controls and display | LED display (4 state-of-charge LEDs), ON/OFF button, ADS DIP switch for the unit address |
| Felicity inverters / RS485 | port G, grey communication cable |
|---|---|
| Inverters of other brands / CAN | port H PCS, pins 7 CANL-PCS and 8 CANH-PCS, blue communication cable |
| Inverters of other brands / RS485 | port H PCS, pins 5 RS485-B and 6 RS485-A |
| Parallel communication between batteries | ports LINK-0 and LINK-1, black communication cable |
| Felicity inverters | RS485 communication (port G, grey cable) |
| Inverters of other brands | the manufacturer states compatibility with leading inverter brands (CAN or RS485 communication via the PCS port) |
| Inverter settings without communication | max. charge voltage 57.6 V, float voltage 57.6 V, max. charge current 60 A × N, cut-off voltage 48 V |
| Compatible inverters | Felicity inverters, inverters of leading brands as stated by the manufacturer |
| and others | as stated by the manufacturer |
| Protection degree | IP65 |
| Installation | On a wall or on the floor, always upright; indoors or outdoors out of direct sunlight |
| Charging temperature | 0 to +55 °C |
| Discharging temperature | −20 to +55 °C |
| Storage temperature | 0 to +35 °C |
| Relative humidity | 5–95% |
| Altitude | up to 2,000 m |
| Dimensions (L × W × H) | 665 × 440 × 175 mm |
| Net weight | 48.5 kg |
| Gross weight | 64.5 kg |
| Package dimensions | 760 × 540 × 345 mm |
| Manufacturer warranty | 10 years (according to the manufacturer’s warranty terms) |
| Package contents | Battery, user manual, quick guide, warranty card, wall bracket, 2 power cables 0.9 m / 25 mm², 2 crimp terminals, communication cables (grey, blue, yellow, black), 2 signal terminals, 8 handle screws, 5 plastic screws for the bracket |
| Certification: battery safety | IEC 62619:2022, CB Scheme (TÜV Rheinland, JPTUV-180618) |
| Certification: CE-EMC | EN IEC 61000-6-1, -6-2, -6-3, -6-4 (SZNTC2502088EV00) |
| Certification: transport | UN38.3 |
Wall-mounted LiFePO4 battery, 5.12 kWh, IP65
The Felicity LPBA48100-OL is a low-voltage battery unit with LiFePO4 cells, a nominal voltage of 51.2 V and a capacity of 100 Ah, which gives a nominal energy of 5.12 kWh. It is intended for residential and small commercial photovoltaic systems with an inverter that works with a battery voltage of around 48 V. The battery stores surplus solar energy and returns it in the evening and at night or during a grid outage, provided the inverter supports this.
The unit is designed to be mounted upright on a wall using the supplied bracket, or it can be placed on the floor. It measures 665 × 440 × 175 mm and weighs 48.5 kg, with a handle for carrying. IP65 protection is considerably higher than that of common plug-in battery modules, which is why the manufacturer permits installation both indoors and outdoors, as long as it is out of direct sunlight. The ports, the control button and four LEDs showing the state of charge are located on the side.
Voltage, currents and depth of discharge
The operating voltage of the battery is 44.8–57.6 V. The recommended charge and discharge current is 50 A, the maximum continuous current is 60 A and the peak current is 100 A for 15 s. The manufacturer notes that the continuous current depends on temperature and state of charge, so in the cold or with a nearly full or empty battery the actual current may be lower. The depth of discharge is at least 95% according to the manufacturer, so a large part of the nominal energy is actually usable.
With parallel connection the currents of the individual batteries add up. The system voltage always stays at 51.2 V, because the units are placed side by side rather than in series.
Cycle life and operating conditions
The manufacturer specifies a cycle life of at least 6,000 cycles at a current of 0.2C, a temperature of 25 °C and a depth of discharge of 80%. When comparing with other batteries, keep the test conditions in mind, because the number of cycles is stated by different manufacturers for different depths of discharge, currents and temperatures.
Charging is possible from 0 to +55 °C, discharging from −20 to +55 °C and storage at 0 to +35 °C. Relative humidity may be 5–95% and the altitude up to 2,000 m. According to the manual, the optimum ambient temperature is 20–30 °C.
Safety: BMS, breaker, fuse and aerosol fire-extinguishing system
The built-in smart BMS monitors voltage, current and temperature, and the unit includes a breaker and a fuse. According to the manufacturer, the fuse can be replaced from the outside without opening the battery. In case of overcurrent the battery reports a fault after 15 s and recovers automatically after one minute.
The battery is equipped with an aerosol fire-extinguishing system and a vent valve. Series connection of units is not supported.
Parallel connection and addressing
The capacity of the system can be increased by connecting units in parallel. According to the datasheet, up to 12 batteries can be connected in parallel, giving a total of 61.44 kWh. Series connection is not supported: the units are connected in parallel, so the system voltage remains 51.2 V nominal while capacity and available current increase.
The power conductors are joined through a combiner box (the manufacturer recommends the BTCB0606 and BTCB0303 types) or through a copper busbar. Parallel communication between the batteries runs over the black cables between the LINK-0 and LINK-1 ports. Each unit in a parallel group has its own address, which you set with the ADS DIP switch on the side: the control unit (master) has switches 1 and 5 on, and the addresses of the other units are listed in the manual’s table. The inverter and cabling work with the sum of the currents of all parallel-connected units.
How to choose an inverter and communication
The battery has two communication ports for the inverter. Port G uses RS485 communication and is intended for Felicity inverters, which are connected with the grey cable from the package. The PCS port H is used for communication with hybrid inverters of other brands over CAN or RS485, using the blue cable or the yellow universal RJ45 cable with eight loose wires, which the customer wires according to the inverter documentation.
The PCS port wiring on the battery side according to the manual is: pin 1 COM-GND, pin 5 RS485-B, pin 6 RS485-A, pin 7 CANL-PCS and pin 8 CANH-PCS. On the inverter side, pins 7 CANL-PCS and 8 CANH-PCS are connected for CAN. The battery is compatible with leading inverter brands. The battery communicates with inverters via CAN or RS485 as a 51.2 V LiFePO4 battery.
Installation and handling
The unit is installed upright. On a wall it is fixed with the supplied wall bracket and plastic screws; on the floor it is placed so that it stands stably and remains accessible. Installation is possible both indoors and outdoors, out of direct sun. After the power cables and communication have been connected, the battery is switched on with the ON/OFF button.
For carrying, a handle fixed with eight screws is provided; the weight is 48.5 kg, 64.5 kg in the package. The power terminals on the cables are crimped, the cables have a cross-section of 25 mm² and are rated for up to 125 A. The PE earth connection is always made.
Package contents and certification
The package contains the user manual, a quick guide, a warranty card, a wall bracket, two power cables 0.9 m / 25 mm² with two crimp terminals, four communication cables (grey for Felicity inverters, blue for CAN and RS485 of other brands, yellow universal RJ45 to eight wires and black for parallel connection), two signal terminals, eight handle screws and five plastic screws for the bracket.
For the LPBA48100-OL model the following manufacturer documents are available: an IEC 62619:2022 report under the CB scheme (TÜV Rheinland, certificate JPTUV-180618, report CN25NXA4 001, issued 25 November 2025), an electromagnetic compatibility test to EN IEC 61000-6-1, -6-2, -6-3 and -6-4 (report SZNTC2502088EV00 of 20 February 2025) and a UN38.3 transport test (test summary GDFLS2F2P02G01). The manufacturer warranty is 10 years according to the warranty terms.
AI search description
The Felicity LPBA48100-OL is a wall-mounted low-voltage LiFePO4 battery, 51.2 V / 100 Ah, 5.12 kWh, operating voltage 44.8–57.6 V. Recommended current 50 A, continuous up to 60 A, peak 100 A for 15 s, depth of discharge of at least 95%, cycle life of at least 6,000 cycles. Up to 12 units in parallel (61.44 kWh); series connection is not supported. RS485 communication for Felicity inverters and CAN or RS485 for inverters of other brands, LED display. Built-in smart BMS, breaker, fuse and aerosol fire-extinguishing system, IP65. Wall or floor installation, 665 × 440 × 175 mm, 48.5 kg. IEC 62619:2022, CE-EMC and UN38.3 certification, 10-year manufacturer warranty.
Product page: https://batterado.com/product/felicity-lpba48100-ol/










Reviews
There are no reviews yet.