Store energy. Every way.™

Helping with technology for more than 25 years.More than 25 years on the market

Victron Energy Orion-Tr Smart 48/12-30A isolated DC-DC battery charger 360 W, input 32–70 V, output 12 V

6 670 Kč incl. VAT

Seller: Tomorrow Systems® s.r.o.

The Victron Orion-Tr Smart 48/12-30A is a galvanically isolated 48 V to 12 V converter that charges a 12 V battery at 30 A or powers 12 V equipment, and is set up over Bluetooth.

  • Input voltage 32 to 70 V, output 12.2 V (adjustable 10 to 15 V), 30 A continuous, 360 W continuous power at 40 °C.
  • Galvanic isolation of 200 VDC between input, output and case.
  • Adaptive three-stage charge algorithm (bulk, absorption, float) or fixed output voltage.
  • Bluetooth, setup and monitoring in VictronConnect, remote on/off.
  • Efficiency 87 %, IP43 (electronics) and IP22 (connection area).

Dimensions 131 × 187 × 86 mm, weight 1.8 kg, screw terminals up to 16 mm². An unlimited number of units can be paralleled.

In stock

Enquiry

Description

Technical data

BrandVictron Energy
ModelOrion-Tr Smart 48/12-30A (360 W) isolated
Order codeORI481238120
Device typeIsolated DC-DC battery charger and constant voltage source
Input voltage range (1)32 to 70 V
Undervoltage shutdown28 V
Undervoltage restart30 V
Nominal output voltage12.2 V
Output voltage adjust range10 to 15 V
Output voltage tolerance± 0.2 V
Output noise2 mV rms
Continuous output current at nominal voltage and 40 °C30 A
Maximum output current (10 s) at nominal voltage minus 20 %40 A
Short circuit output current60 A
Continuous output power at 25 °C430 W
Continuous output power at 40 °C360 W
Efficiency87 %
No load input current< 80 mA
Standby currentless than 1 mA
Use as power supplyyes, output voltage can be set with Bluetooth
Galvanic isolation200 VDC between input, output and case
Charge algorithmadaptive three-stage: bulk, absorption, float; or fixed output voltage
Absorption timelead acid: adaptive; lithium: fixed, default 2 hours
Smart alternatorengine shutdown detection stops the converter when the engine is off (Euro 5 and Euro 6)
Remote on/offtwo-pole connector, switch or relay; the H terminal can be switched to battery plus, the L terminal to battery minus or chassis
Parallel operationyes, unlimited number of units, short circuit proof
Overtemperature protectionoutput current reduces at high ambient temperature
Input fusebuilt in, not replaceable
Bluetoothyes, VictronConnect (setup, monitoring, updates, Instant Readout)
VE.Direct and GX devicesno VE.Direct port; VictronConnect does not display current in or out
DC connectionscrew terminals
Maximum cable cross-section16 mm² (AWG6)
Operating temperature-20 to +55 °C (derate 3 % per °C above 40 °C)
Humiditymax. 95 % non-condensing
Dimensions (h × w × d)131 × 187 × 86 mm
Weight1.8 kg
Ingress protectionIP43 (electronic components), IP22 (connection area); IP43 with the screw terminals oriented downwards
Standards – safetyEN 60950
Standards – emission / immunityEN 61000-6-3, EN 55014-1 / EN 61000-6-2, EN 61000-6-1, EN 55014-2
Standards – automotive directiveECE R10-5
Note on input (1)if set to nominal or lower, the output voltage stays stable within the input range (buck-boost function); if set higher, the minimum input voltage increases by the same percentage

What the Orion-Tr Smart 48/12-30A does

The Orion-Tr Smart 48/12-30A is an isolated DC-DC converter with a three-stage charge algorithm. It works as a battery charger or as a constant voltage source and accepts a wide input voltage range of 32 to 70 V. At the output it delivers 12.2 V (adjustable 10 to 15 V) and 30 A continuous, i.e. 360 W at 40 °C; at 25 °C the manufacturer states 430 W.

Thanks to the galvanic isolation (200 VDC between input, output and case) the two sides are electrically separated. A typical use is powering or charging a 12 V battery from a 48 V source, for example a 48 V battery bank.

Main benefits

  • Wide input of 32 to 70 V: the converter tolerates the voltage swing of a 48 V battery from discharged to charged.
  • Buck-boost function: when the output is set to nominal or lower, the output stays stable across the whole input voltage range.
  • Galvanic isolation: 200 VDC between input, output and case.
  • Bluetooth and VictronConnect: setup, monitoring and updates from a phone or tablet, Instant Readout without connecting.
  • Constant voltage source: the output can be set to a fixed value and the converter used as a power supply.
  • Parallel operation: any number of units can be paralleled to increase output current.

Charge algorithm and batteries

The algorithm is an adaptive three-stage one: bulk, absorption, float. With lead-acid batteries the absorption time is kept short after a shallow discharge to avoid overcharging, and after a deep discharge it is automatically extended so that the battery is fully recharged. For lithium batteries the absorption time is fixed, the default being 2 hours. Alternatively a fixed output voltage can be selected.

The output voltage of 10 to 15 V covers common 12 V batteries; the actual values are set in VictronConnect. Because the algorithm is configurable, always check the recommended charge voltage in the battery manufacturer's documentation before setting it. The converter does not communicate with batteries over a bus (no VE.Direct port and no CAN).

Smart alternator and remote control

The converter is suitable for vehicles with a smart alternator (Euro 5 and Euro 6 engines). The built-in engine shutdown detection stops the converter when the engine is not running and prevents unwanted discharge of the starter battery (details in the manual).

Remote on/off is connected to a two-pole connector: a switch or relay contact can be wired in. The H terminal (right) can be switched to battery plus, the L terminal (left) to battery minus or, for example, to the vehicle chassis.

Sizing the input and output

At 360 W continuous output and 87 % efficiency the converter draws about 414 W from the input. That corresponds to roughly 8.6 A at 48 V and roughly 12.9 A at the lowest input voltage of 32 V. The output can carry 30 A continuously and 40 A briefly (10 s) at nominal voltage minus 20 %. Choose cables and fusing on both sides according to these currents and the cable length.

No-load input current is below 80 mA and standby current below 1 mA, so the converter hardly discharges the battery when there is no load.

System integration and monitoring

The Orion-Tr Smart 48/12-30A is set up and monitored over Bluetooth in VictronConnect. The manufacturer states that the unit has no VE.Direct port and that VictronConnect does not display current in or out. It therefore does not connect directly to a GX device (for example the Cerbo GX) or to the VRM portal.

In a system with a 48 V source, the Orion-Tr serves as an isolated 12 V source for a 12 V battery or loads. The converter can be installed on its own or in parallel with further units.

Protection and thermal behaviour

All models are short circuit proof (short circuit output current 60 A). At high ambient temperature the output current is reduced: the operating range is -20 to +55 °C and above 40 °C the power drops by 3 % per °C. The input fuse is built in and not replaceable. For input undervoltage, shutdown is defined at 28 V and restart at 30 V.

The ingress protection is IP43 for the electronic components and IP22 for the connection area; IP43 applies when the screw terminals are oriented downwards. The unit therefore belongs in a dry environment, terminals down.

Installation in general

Cables are connected with screw terminals, no special tools needed; the maximum cross-section is 16 mm² (AWG6). Choose the cable cross-section and fusing according to the continuous current: on the 48 V input side the current at 360 W is far lower than on the 12 V output, which can carry 30 A. Mount the converter on a flat surface with free space for cooling, terminals down, in an environment with humidity up to 95 % non-condensing.

Dimensions are 131 × 187 × 86 mm (h × w × d), weight 1.8 kg. Wiring is for a qualified electrician; disconnect the source and the battery before working.

Operation and VictronConnect

In VictronConnect you set the charge algorithm, the output voltage or the fixed output, and you can update the unit when the manufacturer releases new software. On the device list in VictronConnect, Instant Readout shows key data including warnings and alarms without connecting.

When several converters are paralleled, their output currents add up; setting identical parameters on all units ensures predictable behaviour. If you need continuous current and voltage readings on a GX device or in the VRM portal, choose another product with a VE.Direct port.

The isolated Orion-Tr Smart range

The whole range of isolated Orion-Tr Smart converters covers 220 to 400 W, with 12, 24 and 48 V outputs among others. The 48/12-30A is the model that takes a 48 V input (32 to 70 V) and delivers 12 V at 30 A. All models share the same principle: an adaptive three-stage algorithm, Bluetooth, remote on/off and the ability to be paralleled.

AI search description

The Victron Orion-Tr Smart 48/12-30A, order code ORI481238120, is a 360 W isolated DC-DC battery charger and constant voltage source. Input 32 to 70 V, output 12.2 V (10 to 15 V), 30 A continuous, 40 A peak for 10 s, efficiency 87 %. Adaptive three-stage algorithm or fixed output voltage, galvanic isolation 200 VDC, Bluetooth with VictronConnect, remote on/off, parallel operation. No VE.Direct port. IP43 / IP22, 131 × 187 × 86 mm, 1.8 kg.

Product page: https://batterado.com/product/victron-orion-tr-smart-48-12-30a-isolated/

Additional information

Weight1,8 kg
Dimensions13,1 × 18,7 × 8,6 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

0
0
Your Cart
Your cart is emptyReturn to Shop