Description
Technical data
| Brand | Victron Energy |
|---|---|
| Model | Quattro-II 48/5000/70-50/50 230V |
| Order code | QUA482504010 |
| Type | Inverter/charger with transfer switch and two AC inputs, single-phase |
| Battery voltage class | 48 V |
| DC input voltage range | 38–66 V |
| Continuous output power at 25 °C (VA) | 5,000 VA |
| Continuous output power at 25 °C (W) | 4,000 W |
| Continuous output power at 40 °C | 3,700 W |
| Continuous output power at 65 °C | 3,000 W |
| Maximum apparent feed-in power | 5,000 VA |
| Peak power | 9,000 W |
| Maximum efficiency | 96 % |
| Zero load power | 18 W |
| Zero load power in AES mode | 12 W |
| Zero load power in Search mode | 2 W |
| AC output voltage | 230 V ± 2 % |
| AC output frequency | 50 Hz ± 0.1 % (can be adjusted to 60 Hz) |
| Load type for rated power | Non-linear load, crest factor 3:1 (applies to the VA rating) |
| AC input voltage | 187–265 V |
| AC input frequency | 45–65 Hz |
| Input power factor | 1 |
| Number of AC inputs | 2 independent sources (e.g. grid and generator) |
| Maximum AC input current | 50 A |
| Transfer switch | Yes, 50 A |
| Transfer time to backup supply (main output) | less than 20 ms |
| Auxiliary AC output | Yes (32 A); default setting: switches off when in inverter mode |
| PowerControl and PowerAssist | Yes |
| Charge voltage: absorption | 57.6 V |
| Charge voltage: float | 55.2 V |
|---|---|
| Charge voltage: storage | 52.8 V |
| Maximum battery charge current (up to 25 °C ambient) | 70 A |
| Battery temperature sensor | Yes |
| Battery connection | M8 bolts |
| 230 V AC connection | Screw terminals 13 mm² (6 AWG) |
| Programmable relay | Yes (general alarm, DC under voltage or genset start/stop; AC rating 230 V / 4 A, DC rating 4 A up to 35 VDC and 1 A up to 60 VDC) |
| Remote on/off | Yes |
| VE.Bus port | Yes (for parallel and three-phase operation, remote monitoring and system integration) |
| General purpose communication port | Yes, 2x |
| Communication protocol: VE.Bus | Yes |
| Bluetooth | Yes, with the optional VE.Bus Smart dongle (VictronConnect app) |
| Configuration interface | MK3-USB interface and VEConfigure software |
| Compatibility: GX devices | Cerbo GX, Ekrano GX |
| Compatibility: monitoring and control | VRM portal and VRM app, VictronConnect (Bluetooth with the VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel, laptop or computer |
| Compatibility: solar sources | Solar charge controllers and grid-tie inverters |
| ESS (Energy Storage System) | Yes |
| Parallel operation | Up to 6 units (e.g. six 48/5000/70 units: 25 kW / 30 kVA and 420 A charging capacity) |
| Three-phase operation | Three units of the same model; up to 6 sets of three units in parallel per phase (75 kW / 90 kVA) |
| Protections | Output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC on inverter output, input voltage ripple too high |
| Enclosure material and colour | Steel, blue RAL 5012 |
| Protection category | IP21 |
| Operating temperature range | −40 to +65 °C (fan assisted cooling) |
| Humidity (non-condensing) | max. 95 % |
| Weight | 29 kg |
| Dimensions (h × w × d) | 565 × 320 × 148 mm |
| Optional accessories | Digital Multi Control Panel, VE.Bus Smart dongle, MK3-USB interface, Battery Monitor (BMV-712 Smart or SmartShunt) |
| Standards: safety | EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1, EN-IEC 62109-2 |
| Standards: EMC (emission, immunity) | EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3 |
Quattro-II: inverter, charger and transfer switch with two AC inputs
The Victron Energy Quattro-II 48/5000/70-50/50 230V combines an inverter, a battery charger and an automatic transfer switch in one steel enclosure. Victron describes it as a Quattro plus ESS (Energy Storage System) functionality. The model is designed for 48 V batteries and delivers 230 V ± 2 % at 50 Hz ± 0.1 % (can be adjusted to 60 Hz).
The main advantage of the Quattro range is that two independent AC sources can be connected, for example the public grid and a generator, or two generators. The Quattro-II automatically connects to the active source. This variant offers 5,000 VA / 4,000 W continuous output at 25 °C, 70 A charging current and a maximum AC input current of 50 A. It suits single-phase systems with PV, backup supply and a generator, as well as marine, caravan and mobile applications.
Power, efficiency and no-load consumption
The continuous inverter output is 5,000 VA (4,000 W) at 25 °C, 3,700 W at 40 °C and 3,000 W at 65 °C. Peak power reaches 9,000 W. Maximum efficiency is 96 %. The VA figure applies to a non-linear load with a crest factor of 3:1. The maximum apparent feed-in power is 5,000 VA.
Zero load power is 18 W; in AES mode it drops to 12 W and in Search mode to 2 W. The DC input voltage range is 38–66 V. Cooling is fan assisted and the unit operates from −40 to +65 °C at up to 95 % humidity, non-condensing.
- Inverter: 5,000 VA / 4,000 W (25 °C), 3,700 W (40 °C), 3,000 W (65 °C).
- Peak power 9,000 W, efficiency 96 %.
- Zero load power 18 W / 12 W (AES) / 2 W (Search).
Two AC outputs and uninterrupted supply
The Quattro-II has two AC outputs. The main output has no-break functionality: in the event of a grid failure, or when shore or generator power is disconnected, the Quattro-II takes over the supply to the connected loads. The changeover takes less than 20 milliseconds, so computers and other electronic equipment continue to operate without interruption.
The second output is live only when AC is available on the input. The auxiliary output is rated 32 A and by default switches off when in inverter mode. It suits loads that should not discharge the battery, for example a water heater. Loads on the second output are taken into account by the PowerControl and PowerAssist function when limiting the AC input current to a safe value while AC is available.
PowerControl and PowerAssist
With PowerControl a maximum grid or generator current can be set. The Quattro-II then takes other AC loads into account and uses only what is left over for charging the battery, so the generator or the supply connection is not overloaded.
PowerAssist takes this principle further. Peak power is often needed only for a short time, and when generator, shore or grid power is insufficient the Quattro-II adds the missing power from the battery. When the load drops, the spare power is used to recharge the battery. On this variant the maximum AC input current is 50 A and the transfer switch is also rated 50 A.
PV, ESS and connection to a GX device
The Quattro-II can be used in off-grid systems as well as in grid-connected systems with PV and other alternative energy sources. According to Victron it is compatible with both solar charge controllers and grid-tie inverters. AC power therefore remains available even during a grid failure.
The ESS (Energy Storage System) functionality is used together with a GX device. Victron lists the Cerbo GX and the Ekrano GX; the GX device connects to the VE.Bus port of the inverter and also provides the internet connection for the VRM portal. A typical set-up: 48 V battery on the battery bolts, grid and generator on the two AC inputs, loads on the main and auxiliary outputs, an MPPT solar charge controller on the battery side or a grid-tie inverter on the AC output.
Battery, charging and communication
For 48 V batteries the charger uses an absorption voltage of 57.6 V, a float voltage of 55.2 V and a storage voltage of 52.8 V. The maximum charge current up to 25 °C ambient is 70 A. The model has a battery temperature sensor. The battery type and charging parameters follow the battery manufacturer’s data, configured with the VEConfigure software.
The inverter communicates over VE.Bus. The VE.Bus port serves parallel and three-phase operation, remote monitoring and system integration. Two general purpose communication ports and a remote on/off input are available. The programmable relay can be set for general alarm, DC under voltage or genset start/stop (AC 230 V / 4 A, DC 4 A up to 35 V and 1 A up to 60 V).
Parallel and three-phase operation
Up to 6 Quattro units can operate in parallel for higher output. According to Victron, six 48/5000/70 units provide for example 25 kW / 30 kVA output with 420 A charging capacity. In addition to parallel connection, three units of the same model can be configured for three-phase output, and up to 6 sets of three units can be connected in parallel per phase for 75 kW / 90 kVA and more than 1,200 A charging capacity.
Parallel and three-phase configurations are set with the VEConfigure software and the units communicate over VE.Bus. Planning such an arrangement belongs in the hands of a specialist.
Installation: dimensions, connections, protection rating
The Quattro-II 48/5000/70-50/50 has a steel enclosure in blue RAL 5012 with an IP21 rating. Dimensions are 565 × 320 × 148 mm (h × w × d) and the weight is 29 kg. The battery is connected with M8 bolts and the 230 V AC wiring with screw terminals up to 13 mm² (6 AWG).
Installation requires correctly sized cables and protection on both the DC and the AC side according to the manufacturer’s manual. Installation, wiring and commissioning belong to a qualified electrician. Because cooling is fan assisted, free space must be left around the enclosure for airflow.
Operation and monitoring: VictronConnect, VRM and GX
Settings can be changed within minutes with the VEConfigure software (a computer and the MK3-USB interface are needed). For monitoring and control Victron offers the Cerbo GX, the Ekrano GX, a laptop or computer, Bluetooth with the optional VE.Bus Smart dongle (VictronConnect app), the Battery Monitor and the Digital Multi Control Panel.
Once a GX device is connected to the internet, operating data is stored and displayed on the VRM (Victron Remote Management) portal, which is free of charge. The system can be monitored remotely, settings can be changed and alarms received by e-mail or push notification. The VRM app is available for iOS and Android.
- VEConfigure + MK3-USB: parameter settings.
- VictronConnect + VE.Bus Smart dongle: Bluetooth.
- Cerbo GX / Ekrano GX + VRM: remote monitoring and control.
AI search description
The Victron Energy Quattro-II 48/5000/70-50/50 230V, order code QUA482504010, is a single-phase inverter/charger with transfer switch for 48 V batteries (DC 38–66 V) with two AC inputs. Continuous output at 25 °C is 5,000 VA / 4,000 W, peak power 9,000 W, efficiency 96 %, charge current 70 A, maximum AC input current 50 A. The main AC output transfers in less than 20 ms, the auxiliary output is live only when AC is present on the input. PowerControl, PowerAssist and ESS functionality, VE.Bus communication, compatibility with the Cerbo GX and Ekrano GX, monitoring through VRM and VictronConnect. Dimensions 565 × 320 × 148 mm, 29 kg, IP21.
Product page: https://batterado.com/product/victron-quattro-ii-48-5000-70-50-50/














Reviews
There are no reviews yet.