Description
Technical data
| Brand | Victron Energy |
|---|---|
| Model | Quattro 48/10000/140-100/100 230V |
| Order code | QUA481030010 |
| Type | Inverter/charger with transfer switch and two AC inputs, single-phase |
| Nominal battery voltage | 48 V |
| DC input voltage range | 38–60 V |
| Continuous output power at 25 °C (VA) | 10,000 VA |
| Continuous output power at 25 °C (W) | 8,000 W |
| Continuous output power at 40 °C | 6,500 W |
| Continuous output power at 65 °C | 4,500 W |
| Load type for the VA rating | Non-linear load, crest factor 3:1 |
| Peak power | 20,000 W |
| Input current (A DC) | 235 A |
| Maximum continuous output current (A AC) | 37 A |
| Power factor range | ±0.8 |
| Maximum output fault current | 100 A for 1 s |
| Maximum efficiency | 96 % |
| Zero load power | 60 W |
| Zero load power in AES mode | 40 W |
| Zero load power in Search mode | 15 W |
| AC output voltage | 230 V ± 2 % |
| AC output frequency | 50 Hz ± 0.1 % (can be adjusted to 60 Hz) |
| Number of AC inputs | 2 independent sources (e.g. grid and generator) |
| AC input voltage range | 187–250 V |
| AC input frequency | 50/60 Hz |
| Input power factor (cos φ) | > 0.8 |
| Maximum feed-through current (each input) | 2 x 100 A |
| Short-time withstand current ICw | 10 kA for 30 ms |
| Integrated transfer switch | Yes |
| Transfer time to backup supply (main output) | less than 20 ms |
| Auxiliary AC output | Yes (50 A); switches off when no external AC source is available |
| PowerControl and PowerAssist | Yes |
|---|---|
| Charge voltage: absorption | 57.6 V |
| Charge voltage: float | 55.2 V |
| Charge voltage: storage | 52.8 V |
| Maximum battery charge current (up to 25 °C ambient) | 140 A |
| Battery temperature sensor | Not included with 48 V models, order number ASS000001000 |
| Battery connection | Four M8 bolts (2 plus and 2 minus connections) |
| 230 V AC connection | Bolts M6 |
| Programmable relays | 3x (general alarm, DC under voltage or genset start/stop; AC rating 230 V / 4 A, DC rating 4 A up to 35 VDC and 1 A up to 60 VDC) |
| Remote on/off | Yes |
| VE.Bus port | Yes (for parallel and three-phase operation, remote monitoring and system integration) |
| General purpose communication port | Yes, 2x |
| Communication protocol: VE.Bus | Yes |
| Compatibility: GX devices | Cerbo GX and other GX devices, Ekrano GX |
| Compatibility: monitoring and control | VRM portal and VRM app, VictronConnect (Bluetooth Smart), Battery Monitor, Multi Control Panel, smartphone or tablet, laptop or computer (USB or RS232) |
| Compatibility: solar sources | MPPT solar chargers and grid-tie inverters; loss of mains detection software is available |
| Compatibility: batteries | According to Victron compatible with lithium-ion batteries; settings according to the battery manufacturer’s data |
| Configuration | Stand-alone: DIP switch setting; parallel and three-phase: VE.Bus Quick Configure and VE.Bus System Configurator; off-grid and grid-interactive: Assistants |
| Three-phase operation | Three units of the same model; sets of three units can be connected in parallel (for the Quattro 3–15 kVA range up to 4 sets of three 15 kVA units) |
| Protections | Output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC on inverter output, input voltage ripple too high |
| Enclosure material and colour | Aluminium, blue RAL 5012 |
| Protection category and overvoltage category | IP20, pollution degree 2, OVC III |
| Operating temperature range | −20 to +60 °C |
| Humidity (non-condensing) | max. 95 % |
| Maximum altitude | 2000 m |
| Weight | 51 kg |
| Dimensions (h × w × d) | 470 × 350 × 280 mm |
| Optional accessories | Multi Control Panel, VE.Bus Smart dongle, MK3-USB interface, Battery Monitor (BMV-712 Smart or SmartShunt), battery temperature sensor ASS000001000 |
| Standards: safety | EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1 |
| Standards: EMC (emission, immunity) | EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3 |
Quattro 10 kVA: inverter, charger and transfer switch with two AC inputs
The Victron Energy Quattro 48/10000/140-100/100 230V combines an inverter, a battery charger and an integrated transfer switch in one aluminium enclosure. It is designed for 48 V batteries and delivers 230 V ± 2 % at 50 Hz ± 0.1 % (can be adjusted to 60 Hz). According to Victron the Quattro range is lithium-ion battery compatible.
The key feature is the connection of two independent AC sources, for example the public grid and a generator, or two generators. The Quattro automatically connects to the active source. The AC input accepts 187–250 V, 50/60 Hz, and each of the two inputs passes a current of up to 100 A. This model offers 10,000 VA / 8,000 W continuous output at 25 °C and 140 A charging current.
Power, efficiency and no-load consumption
The continuous inverter output is 10,000 VA (8,000 W) at 25 °C, 6,500 W at 40 °C and 4,500 W at 65 °C. Peak power reaches 20,000 W and maximum efficiency is 96 %. The VA figure applies to a non-linear load with a crest factor of 3:1. The maximum continuous output current is 37 A, the power factor range ±0.8 and the maximum output fault current 100 A for 1 s.
At rated power the inverter draws 235 A on the DC side. Zero load power is 60 W, 40 W in AES mode and 15 W in Search mode. The DC input voltage range is 38–60 V. The short-time withstand current ICw is 10 kA for 30 ms.
- 10,000 VA / 8,000 W (25 °C), 6,500 W (40 °C), 4,500 W (65 °C).
- Peak power 20,000 W, efficiency 96 %.
- Zero load power 60 W / 40 W (AES) / 15 W (Search).
Two AC outputs and uninterrupted supply
The Quattro has two AC outputs. The main output has no-break functionality: in the event of a grid failure, or when shore or generator power is disconnected, the Quattro takes over the supply to the connected loads. The changeover takes less than 20 milliseconds, so computers and other electronic equipment continue to operate without interruption.
The second output is live only when AC is available on one of the Quattro inputs, and it switches off when no external AC source is available. It is rated 50 A and suits loads that should not discharge the battery, for example a water heater.
PowerControl and PowerAssist
The Quattro is a very powerful battery charger and can therefore draw a lot of current from the source. The PowerControl function allows a current limit to be set on each AC input. The Quattro then takes other AC loads into account and uses only what is left over for charging, so the generator or the mains supply is not overloaded. Victron gives the example of a 16 A generator or shore supply per 5 kVA Quattro at 230 V.
PowerAssist extends the principle: peak power is often needed only for a short time, and when mains or generator power is insufficient the Quattro immediately adds the missing power from the battery. When the load drops, the spare power is used to recharge the battery.
PV, ESS and connection to a GX device
The Quattro can be used in off-grid systems as well as in grid-connected systems with PV and other alternative energy sources. According to Victron, loss of mains detection software is available. In off-grid, grid-interactive and self-consumption applications involving grid-tie inverters and/or MPPT solar chargers, settings can be made with Assistants, dedicated software for specific applications.
For monitoring and control a Cerbo GX or another GX device can be connected, among them the Ekrano GX. The GX device connects to the VE.Bus port of the inverter and provides access to the VRM portal. A typical set-up: 48 V battery on the four M8 bolts, grid and generator on the two AC inputs, loads on the main and second output, optionally an MPPT solar charge controller on the battery side.
Battery, charging and communication
For 48 V batteries the charger uses an absorption voltage of 57.6 V, a float voltage of 55.2 V and a storage voltage of 52.8 V. The maximum house battery charge current up to 25 °C ambient is 140 A. The battery temperature sensor is not included with 48 V models; it is available as an accessory under order number ASS000001000. The battery type and charging parameters follow the battery manufacturer’s data.
Communication runs over VE.Bus; the port serves parallel and three-phase operation, remote monitoring and system integration. Two general purpose communication ports, a remote on/off input and three programmable relays are available (general alarm, DC under voltage or genset start/stop; AC 230 V / 4 A, DC 4 A up to 35 V and 1 A up to 60 V).
Three-phase operation and capacity expansion
Three units can be configured for a three-phase output. For the Victron Quattro 3–15 kVA, up to 4 sets of three 15 kVA units can additionally be connected in parallel for 144 kW / 180 kVA and 2,400 A charging capacity. A split-phase option is also available (240 V / 60 Hz) by means of an autotransformer for a “European” inverter.
A stand-alone unit is set with a DIP switch procedure. Parallel and three-phase applications are configured with the VE.Bus Quick Configure and VE.Bus System Configurator software. Planning these arrangements belongs in the hands of a specialist.
Installation: dimensions, connections, protection rating
The Quattro 48/10000/140-100/100 has an aluminium enclosure in blue RAL 5012 with an IP20 rating, pollution degree 2 and overvoltage category OVC III. Dimensions are 470 × 350 × 280 mm (h × w × d) and the weight is 51 kg. The battery is connected with four M8 bolts (two plus, two minus connections) and the 230 V AC wiring with M6 bolts.
The operating temperature is −20 to +60 °C at up to 95 % humidity, non-condensing, and the maximum altitude is 2,000 m. IP20 means indoor use. Installation, cable selection and protection belong to a qualified electrician following the manufacturer’s manual. The weight of 51 kg must be considered when planning the installation.
Operation and monitoring: VictronConnect, VRM and GX
For on-site monitoring and control Victron offers the Battery Monitor, the Multi Control Panel, the Cerbo GX or other GX devices, a smartphone or tablet (Bluetooth Smart) and a laptop or computer (USB or RS232).
For remote monitoring and control a Cerbo GX or another GX device is used. Data is stored and displayed on the VRM (Victron Remote Management) portal, which is free of charge. When connected to Ethernet, a system with a GX device can be accessed and its settings changed remotely. The VRM app is available for iOS and Android.
- Bluetooth with the VE.Bus Smart dongle and the VictronConnect app.
- MK3-USB interface for connection to a computer.
- Cerbo GX / Ekrano GX + VRM: remote monitoring and control.
AI search description
The Victron Energy Quattro 48/10000/140-100/100 230V, order code QUA481030010, is a single-phase inverter/charger with integrated transfer switch for 48 V batteries (DC 38–60 V) with two AC inputs (2 x 100 A). Continuous output at 25 °C is 10,000 VA / 8,000 W, peak power 20,000 W, efficiency 96 %, charge current 140 A. The main output transfers in less than 20 ms, the 50 A second output is live only when an AC source is present. PowerControl and PowerAssist, three programmable relays, VE.Bus communication, GX devices including Cerbo GX and Ekrano GX, monitoring in VRM. Dimensions 470 × 350 × 280 mm, 51 kg, IP20.
Product page: https://batterado.com/product/victron-quattro-48-10000-140-100-100/












Reviews
There are no reviews yet.