Description
Technical data
| Brand | Victron Energy |
|---|---|
| Model | MultiPlus-II 48/3000/35-32 230V |
| Order code | PMP482305012 |
| Type | Inverter/charger with transfer switch |
| Nominal battery voltage | 48 V |
| Inverter: DC input voltage range | 38–66 V |
| Inverter: AC output voltage | 230 V ± 2 % |
| Inverter: output frequency | 50 Hz ± 0.1 % (adjustable to 60 Hz) |
| Inverter: continuous power at 25 °C (non-linear load, crest factor 3:1) | 3,000 VA |
| Inverter: continuous power at 25 °C | 2,400 W |
| Inverter: continuous power at 40 °C | 2,200 W |
| Inverter: continuous power at 65 °C | 1,700 W |
| Inverter: peak power | 5,500 W |
| Inverter: max. apparent feed-in power | 3,000 VA |
| Inverter: max. efficiency | 95 % |
| Inverter: zero load power | 11 W |
| Inverter: zero load power in AES mode | 7 W |
| Inverter: zero load power in Search mode | 2 W |
| Switchover time to inverter (main output) | less than 20 ms |
| AC input: voltage range | 187–265 V |
| AC input: frequency range | 45–65 Hz |
| AC input: max. input current | 32 A |
| Transfer switch | 32 A |
| PowerControl and PowerAssist | yes |
| External AC current sensor (optional) | 100 A (100 A:50 mA) |
| Auxiliary AC output (AC-out-2) | yes (32 A) |
| Charger: absorption voltage | 57.6 V |
| Charger: float voltage | 55.2 V |
| Charger: storage mode voltage | 52.8 V |
|---|---|
| Charger: max. battery charge current (up to 25 °C ambient) | 35 A |
| Battery temperature sensor | not included with 48 V models; order number ASS000001000 |
| Protection | output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, 230 V AC on inverter output, input voltage ripple too high |
| Anti-islanding protection | built-in function |
| Battery connection | M8 bolts |
| AC connection | screw terminals 13 mm² (6 AWG) |
| VE.Bus port | yes (parallel and three-phase operation, remote monitoring and system integration) |
| General purpose communication port | yes, 2× |
| Remote on/off terminal | yes |
| Programmable relay | yes (general alarm, DC undervoltage or genset start/stop; AC 230 V / 4 A, DC 4 A up to 35 V DC and 1 A up to 60 V DC) |
| VE.Bus protocol | connection of units in parallel and three-phase operation, remote monitoring and system integration; the MK3-USB interface connects via RJ45 UTP cable |
| Configuration and remote control | VictronConnect app, VEConfigure software (with MK3-USB interface), VRM portal |
| Compatibility: GX devices | GX devices Cerbo GX, Ekrano GX and other GX products |
| Compatibility: solar systems | solar charge controllers (MPPT) and grid-tie PV inverters |
| Compatibility: monitoring and control | VRM portal, VictronConnect with VE.Bus Smart dongle (Bluetooth), Battery Monitor, Digital Multi Control Panel |
| Parallel operation | up to 6 units |
| Three-phase operation | 3 units of the same model, up to 6 sets in parallel |
| Operating temperature range | −40 to +65 °C (fan-assisted cooling) |
| Humidity (non-condensing) | max. 95 % |
| Maximum altitude | 2000 m |
| Material and colour | steel, blue RAL 5012 |
| Protection category | IP22 |
| Dimensions (h × w × d) | 499 × 268 × 141 mm |
| Weight | 19 kg |
| Standards: safety | EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1, EN-IEC 62109-2 |
| Standards: emission and immunity (EMC) | EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3 |
Compact 3 kVA inverter/charger for a 48 V battery
The Victron Energy MultiPlus-II 48/3000/35-32 230V is a multifunctional inverter/charger that combines a sine-wave inverter, a battery charger and an AC transfer switch in one steel enclosure. Its rated power is 3,000 VA (2,400 W at 25 °C), peak power reaches 5,500 W and efficiency is up to 95 %. The unit is designed for a battery of 48 V nominal voltage; the DC input voltage range is 38–66 V and the output is 230 V ± 2 % at 50 Hz, with the frequency adjustable to 60 Hz.
At 19 kg and 499 × 268 × 141 mm it is a compact model of the range. The MultiPlus-II has all the features of the classic MultiPlus plus an optional external current sensor that extends PowerControl and PowerAssist. It is ideally suited to professional marine, yachting, vehicle and land-based off-grid applications, has built-in anti-islanding functionality and, according to Victron, an increasingly long list of country approvals for ESS (Energy Storage System) applications.
Inverter power, temperature derating and consumption
Continuous power depends on the ambient temperature: 2,400 W at 25 °C, 2,200 W at 40 °C and 1,700 W at 65 °C. The 3,000 VA figure applies at 25 °C for a non-linear load with a crest factor of 3:1, and the same apparent power is the maximum when feeding into the grid. The peak power of 5,500 W covers short-term demands from loads with an increased inrush current. Cooling is fan-assisted and the operating temperature range is −40 to +65 °C.
Zero load power is only 11 W, 7 W in AES mode and 2 W in Search mode. In a system that works at low load or without load most of the time, the inverter’s own consumption therefore puts little strain on the battery. The stated efficiency of 95 % is the maximum value for the 48 V version.
Battery charger and choosing a 48 V battery
The charger delivers a current of up to 35 A (at ambient temperatures up to 25 °C). The absorption voltage is 57.6 V, the float voltage 55.2 V and the storage mode voltage 52.8 V. The AC input voltage range for charging is 187–265 V at 45–65 Hz. The battery temperature sensor is not included with 48 V models; it can be added separately under order number ASS000001000.
When choosing a battery, start from the nominal voltage of 48 V, the DC input voltage range of 38–66 V, the charge voltages given above and the maximum charge current of 35 A. For lithium batteries, follow the battery manufacturer’s specifications and Victron’s documentation on connecting to the BMS. The battery is connected with M8 bolts.
PowerControl, PowerAssist and uninterrupted supply
The PowerControl function lets you set a maximum grid or generator current. The inverter then takes the other AC loads into account and uses only what is left over for battery charging, so neither the generator nor the supply is overloaded. PowerAssist goes a step further: where peak power is needed only briefly, the inverter compensates insufficient generator, shore or grid power with power from the battery, and when the load drops, the spare power is used to recharge the battery. On this model the maximum AC input current and the transfer switch rating are 32 A.
The main output has no break functionality. If the grid fails or the generator or shore power is disconnected, the inverter takes over the supply to the connected loads in less than 20 ms, so computers and other electronic equipment continue to operate without disruption.
Two AC outputs: uninterrupted and auxiliary
The main output supplies critical loads and is backed up from the battery during a grid failure. The second, auxiliary output AC-out-2 (up to 32 A) is live only when AC is available on the input of the inverter. It suits loads that should not discharge the battery, such as a water heater.
Loads on the second output are taken into account by PowerControl and PowerAssist, so the AC input current stays at a safe value as long as AC is available. Loads that should shut down when AC input power is not available can thus be kept separate from the critical loads.
Solar systems, ESS and grid-parallel topology
The MultiPlus-II can be used in off-grid as well as grid-connected systems with photovoltaics and other alternative energy sources. It is compatible with both solar charge controllers and grid-tie PV inverters, so AC power remains available even during a grid failure. In a standard marine, mobile or off-grid application, the inverter sits between the grid or generator, the battery and the critical loads.
In a grid-parallel topology with an MPPT solar charge controller, the inverter uses data from the external AC current sensor (ordered separately; 100 A, ratio 100 A:50 mA) or from a power meter to optimise self-consumption and, if required, to prevent grid feed. In a power outage it continues to supply the critical loads. For the design and configuration of ESS systems, Victron refers to its ESS Design and configuration manual.
Parallel and three-phase operation
Up to 6 units can be operated in parallel for a higher output power. Six 48/3000/35-32 units add up to a combined rated power of 18 kVA and a charge current of 210 A. In addition to parallel connection, three units of the same model can be configured for three-phase output, and up to six such sets of three can be connected in parallel.
The units are interconnected via the VE.Bus port with UTP cables with RJ45 connectors, and the assembly is configured with VEConfigure software using the MK3-USB interface. This allows the system to be extended unit by unit as demands grow.
Communication, monitoring and configuration
The inverter communicates over the VE.Bus. For local and remote monitoring and control, a GX device such as the Cerbo GX or Ekrano GX can be connected; it provides intuitive system control and access to the free VRM (Victron Remote Management) portal. Operational data is stored and displayed in a comprehensive graphical format; once connected to the internet, the system can be accessed and configured remotely, alarms can be received by e-mail or push notification, and the VRM app is available for iOS and Android.
Settings can be changed in a matter of minutes with VEConfigure software (a computer and the MK3-USB interface are needed; the interface connects via an RJ45 UTP cable and plugs into a USB port) or in the VictronConnect app. Further options: Bluetooth with the VE.Bus Smart dongle (which also measures battery voltage and temperature), a Battery Monitor, and the Digital Multi Control Panel with an on/off/charger-only switch, LED readout and a rotary knob for setting PowerControl and PowerAssist levels. The unit has two general purpose communication ports, a remote on/off terminal and a programmable relay (alarm, DC undervoltage or genset start/stop).
Installation, construction and standards
The inverter is housed in a blue steel enclosure (RAL 5012) with IP22 protection and weighs 19 kg. Dimensions (h × w × d) are 499 × 268 × 141 mm. The operating temperature range is −40 to +65 °C with fan-assisted cooling, humidity up to 95 % non-condensing and the maximum altitude is 2000 m. The battery is connected with M8 bolts; AC wiring goes to screw terminals for 13 mm² (6 AWG).
The unit conforms to EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1 and EN-IEC 62109-2 (safety) and EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2 and IEC 61000-6-3 (emission and immunity).
AI search description
The Victron Energy MultiPlus-II 48/3000/35-32 230V (order code PMP482305012) is an inverter/charger with transfer switch for a 48 V battery (DC 38–66 V). Continuous power 3,000 VA, 2,400 W at 25 °C, peak 5,500 W, efficiency up to 95 %, switchover under 20 ms. 35 A charger, PowerControl and PowerAssist, 32 A AC input, two AC outputs (auxiliary 32 A). VE.Bus communication, GX devices Cerbo GX and Ekrano GX, VRM and VictronConnect monitoring. Up to 6 units in parallel or three-phase in sets of three. IP22, 19 kg, 499 × 268 × 141 mm. Use: off-grid, back-up and hybrid systems with photovoltaics.
Product page: https://batterado.com/product/victron-multiplus-ii-48-3000-35-32/














Reviews
There are no reviews yet.